Hướng dẫn sử dụng trung tâm báo cháy Hochiki thường
Hướng dẫn sử dụng trung tâm báo cháy Hochiki thường
Zone của Trung tâm báo cháy. Tên của khu vực được ghi trên mặt Tủ báo cháy.
Khi có cháy hoặc có sự cố ở khu vực nào, đèn của khu vực đó sẽ sáng.
1. TRẠNG THÁI HOẠT ĐỘNG BÌNH THƯỜNG:
Đèn “AC. ON” sáng màu xanh : Hệ thống hoạt động với nguồn 220 VAC.
2. TRẠNG THÁI CÁC ĐÈN HIỂN THỊ :
Đèn “ ZONE” :
- Sáng màu đỏ : Báo động khu vực bị cháy.
- Đèn vàng nhấp nháy : Chỉ sự cố báo lỗi đứt dây tín hiệu hoặc hở mạch Zone. Cần
kiểm tra
và xử lý gấp để hệ thống hoạt động lại bình thường.
Đèn “COMMON ALARM” : sáng màu đỏ. Báo động cháy.
Đèn “COMMON SUPERVISORY”: sáng màu vàng (nếu một Zone được cài đặt
chế độ giám sát Superviory)
Đèn “COMMON TROUBLE” : sáng nhấp nháy màu vàng. Bo lỗi sự cố chung.
Có một hoặc nhiều lỗi cần phải xử lý.
Đèn “BATTERY TROUBLE” : sáng màu vàng. Bình điện dự phòng không
được kết nối hoặc bị hư.
Đèn “GROUND FAULT” : sáng màu vàng. Báo có sự cố nối đất, chạm max.
Đèn “SIGNAL SILENCE” : sáng nhấp nháy màu vàng. Ngắt chuông còi báo
động.
Đèn “AUXILIARY DISC.” : sáng nhấp nháy màu vàng. Ngắt Relay kích hoạt
ngỏ ra ( Supervisory và Alarm).
Đèn “SIG.ZONE TROUBLE ” : sáng nhấp nháy màu vàng. Ngõ kết nối chuông
bị lỗi.
I. THAO TÁC KHI CÓ CHÁY:
Khi có cháy Hệ thống báo cháy thể hiện như sau:
• Đèn Zone tương ứng với khu vực có cháy: sáng.
• Còi chính bên trong tủ báo cháy và chuông khu vực kêu.
1. Quan sát đèn trên Tủ báo cháy để xác định chính xác khu vực có cháy.
2. Khẩn trương tới khu vực có báo động để xác định vị trí cháy.
3. Báo CS PCCC (số: 114) và thực hiện chữa cháy bằng phương tiện tại chỗ.
II. THAO TÁC SAU KHI CHỮA CHÁY:
Sau khi chắc chắn công tác chữa cháy đã hoàn tất, tiến hành khôi phục (RESET)
HTBC trở về điều kiện hoạt động bình thường.
Nếu báo cháy bằng nhấn Hộp báo cháy bằng tay, thì phải Reset Hộp báo cháy
trước khi Reset trung tâm báo cháy. Nếu Reset Trung tâm báo cháy trước khi Reset
Hộp báo cháy, TTBC sẽ tiếp tục báo động trở lại.
• Kéo nút “System Reset” theo chiều mũi tên để khôi phục (Reset) hệ thống
• Sau khi đã RESET xong, phải chắc chắn hệ thống trở về trạng thái hoạt động bình
thường:
- Đèn báo nguồn điện xoay chiều “A.C. ON” sáng
III. THAO TÁC KHI BÁO SỰ CỐ:
- Tham khảo tài liệu kèm theo TTBC để biết cách phân biệt sự cố.
- Đề nghị thông báo với đơn vị lắp đặt tới kiểm tra, sửa chữa khi Hệ thống có sự
cố.
- Tắt còi báo động chính và chuông:
1. Tắt còi báo động chính: (còi gắn bên trong Tủ báo cháy)
• Khi còi báo động chính kêu.
• Nếu nhấn vào công tắc “Buzzer Silence”, còi báo động tắt. Và đèn “Common
Alarm” sáng.
• Còi báo động sẽ kêu lại nếu TTBC nhận được tín hiệu báo cháy khác.
2. Tắt tiếng chuông/còi báo cháy:
• Nếu công tắc “Signal Silencing” bị nhấn, tất cả chuông báo cháy bị tắt.
LNOTICE
All information, documentation, and specifications contained in this manual are
subject to
change without prior notice by the manufacturer.
HCP 1000 SERIES
Microprocessor Based - Fire Alarm Control Panel
INSTALLATION and OPERATION MANUAL
©2000 by Hochiki America Corporation
Printed September 6, 2000
LT-600HOC Rev.4 (Operating Instruction is NP-739HOC Rev.3)Page 1 of 52
TABLE of CONTENTS
1.0 INTRODUCTION ......... ......... ......... ......... ......... ......... ......... .........
.........Page 3 of 52
1.1 OVERALL FEATURES: ......... ......... ......... ......... ......... ......... .........
.........Page 3 of 52
1.2 CONTROLS AND INDICATORS ......... ......... ......... ......... ......... ......... .........
. . Page 3 of 52
2.0 GENERAL NOTES ......... ......... ......... ......... ......... ......... ......... ......... ........
Page 4 of 52
3.0 SYSTEM COMPONENTS ......... ......... ......... ......... ......... ......... ......... ......... .
. Page 5 of 52
3.1 CHASSIS TYPES ......... ......... ......... ......... ......... ......... ......... ......... ... Page 6
of 52
3.2 SERIES 1000 FIRE ALARM CONTROL PANEL - KITS ......... ......... .........
......... ......... . . Page 6 of 52
4.0 MECHANICAL INSTALLATION and DIMENSIONS ......... ......... .........
......... ......... ........ Page 7 of 52
4.1 MAIN CHASSIS INSTALLATION ......... ......... ......... ......... ......... .........
.........Page 9 of 52
4.2 MAIN & EXPANDER CHASSIS INSTALLATION ......... ......... ......... .........
......... ....... Page 10 of 52
5.0 MODULES MOUNTING LOCATIONS ......... ......... ......... ......... ......... .........
......... . Page 11 of 52
6.0 MODULE SETTINGS ......... ......... ......... ......... ......... ......... ......... ......... ......
Page 14 of 52
6.1 MAIN FIRE ALARM MODULE (Part of Main Chassis) ......... ......... .........
......... ......... ... Page 14 of 52
6.2 MAIN DISPLAY MODULE (Part of Main Chassis) ......... ......... ......... .........
......... ...... Page 15 of 52
6.3 ADDER DISPLAY MODULE (Part of Expander Chassis) ......... ......... .........
......... ......... Page 17 of 52
6.4 DETECTION ADDER MODULE (Model HDM-1008A) ......... ......... .........
......... ......... ... Page 18 of 52
6.5 SIGNAL ADDER MODULE (Model HSGM-1004A) ......... ......... ......... .........
......... ...... Page 18 of 52
6.6 RELAY ADDER MODULE (Model HRM-1008A) ......... ......... ......... .........
......... ........ Page 19 of 52
6.7 DACT/DIALLER MODULE (Model HUDACT-100) ......... ......... ......... .........
......... ....... Page 19 of 52
6.8 POLARITY REVERSAL and CITY TIE MODULE (MODEL: HPR-100)
......... ......... ......... ......... Page 20 of 52
7.0 FIELD WIRING ......... ......... ......... ......... ......... ......... ......... ......... ......... .
Page 21 of 52
7.1 MAIN FIRE ALARM MODULE TERMINAL CONNECTIONS ......... .........
......... ......... ....... Page 21 of 52
7.2 DETECTION MODULE (HDM-1008A) TERMINAL CONNECTIONS .........
......... ......... ......... . Page 23 of 52
7.3 SIGNAL MODULE (HSGM-1004A) TERMINAL CONNECTIONS .........
......... ......... ......... .... Page 24 of 52
7.4 RELAY MODULE (HRM-1008A) TERMINAL CONNECTIONS .........
......... ......... ......... ...... Page 25 of 52
7.5 HUDACT-100 MAIN BOARD TERMINAL CONNECTIONS ......... .........
......... ......... ......... Page 26 of 52
7.6 POLARITY REVERSAL and CITY TIE MODULE (MODEL: HPR-100)
TERMINAL CONNECTIONS ......... ... Page 27 of 52
7.7 POWER SUPPLY CONNECTIONS ......... ......... ......... ......... ......... .........
........ Page 28 of 52
7.8 WIRING TABLES & INFORMATION ......... ......... ......... ......... ......... .........
....... Page 29 of 52
WIRING TABLE FOR INITIATING CIRCUITS ......... ......... ......... ......... .........
......... Page 29 of 52
......... ......... ........ Page 29 of 52
8.0 SYSTEM CHECKOUT ......... ......... ......... ......... ......... ......... ......... ......... ....
Page 30 of 52
8.1 BEFORE TURNING THE POWER "ON" ......... ......... ......... ......... .........
......... .... Page 30 of 52
8.2 POWER-UP PROCEDURE ......... ......... ......... ......... ......... ......... ......... .....
Page 30 of 52
8.3 TROUBLESHOOTING ......... ......... ......... ......... ......... ......... ......... .........
Page 30 of 52
9.0 INDICATORS, CONTROLS, & OPERATION ......... ......... ......... ......... .........
......... ...... Page 31 of 52
9.1 COMMON INDICATORS ......... ......... ......... ......... ......... ......... ......... .......
Page 32 of 52
9.2 COMMON CONTROLS ......... ......... ......... ......... ......... ......... ......... ........
Page 33 of 52
9.3 CIRCUIT STATUS INDICATORS ......... ......... ......... ......... ......... .........
......... . Page 33 of 52
9.4 CIRCUIT (ZONE) DISCONNECT SWITCHES ......... ......... ......... .........
......... ......... Page 34 of 52
9.5 SINGLE STAGE OPERATION ......... ......... ......... ......... ......... ......... ......... ...
Page 34 of 52
9.6 TWO STAGE OPERATION ......... ......... ......... ......... ......... ......... ......... .....
Page 35 of 52
9.7 CIRCUIT TYPES ......... ......... ......... ......... ......... ......... ......... ......... .... Page
36 of 52
10.0 SYSTEM CONFIGURATION ......... ......... ......... ......... ......... ......... .........
......... Page 37 of 52
10.1 INTRODUCTION TO CONFIGURATION ......... ......... ......... ......... .........
......... ... Page 37 of 52
10.2 ENTERING CONFIGURATION MODE ......... ......... ......... ......... .........
......... ..... Page 39 of 52
10.3 EXITING CONFIGURATION MODE ......... ......... ......... ......... ......... .........
....... Page 39 of 52
10.4 FACTORY DEFAULT CONFIGURATION ......... ......... ......... ......... .........
......... ... Page 39 of 52
10.5 RESTORE TO DEFAULT / RESIZE (CLASS A or B) ......... ......... .........
......... ......... ... Page 40 of 52
10.6 RESIZE SYSTEM (SET CIRCUIT ADDER MODULE NUMBER & TYPE)
......... ......... ......... ...... Page 40 of 52
10.7 CONFIGURING FEATURES ......... ......... ......... ......... ......... ......... ......... ....
Page 41 of 52
10.8 CONFIGURING INITIATING AND INDICATING CIRCUITS ......... .........
......... ......... ....... Page 42 of 52
10.9 CONFIGURING CIRCUIT CORRELATIONS ......... ......... ......... .........
......... ......... . Page 42 of 52
10.10 DISPLAY CONFIGURATION ......... ......... ......... ......... ......... ......... .........
... Page 43 of 52
11.0 WALK TEST OPERATION ......... ......... ......... ......... ......... ......... .........
......... . Page 45 of 52Page 2 of 52
APPENDIX "A" - COMPATIBLE DEVICES ......... ......... ......... ......... ......... .........
......... Page 46 of 52
APPENDIX "B" - HRA-1000 REMOTE ANNUNCIATOR PANELS ......... .........
......... ......... ......... . . Page 49 of 52
APPENDIX "C" - MODULE SPECIFICATIONS and FEATURES ......... .........
......... ......... ......... . . Page 50 of 52
APPENDIX "D" - POWER SUPPLY & BATTERY CALCULATIONS
(SELECTION GUIDE) ......... ......... ......... Page 51 of 52
WARRANTY ......... ......... ......... ......... ......... ......... ......... ......... ......... ....... Page
52 of 52
TABLE of FIGURES
Fig.1: HBB-1024 Flush or Surface Enclosure Installation and Dimensions ............
... Page 7 of 52
Fig.1A: HBB-1072 Flush or Surface Enclosure Installation and Dimensions
............ ... Page 8 of 52
Fig.2: Main Chassis Installation ............ ............ ............ ............ . . Page 9 of 52
Fig.3: Expander Chassis Installation ............ ............ ............ .......... Page 10 of 52
Fig.4: Module Mounting Locations ............ ............ ............ ........... Page 12 of 52
Fig.4A: Circuit Adder Module Mounting Details ............ ............ ............ . . Page
13 of 52
Fig.5: Main Fire Alarm Module ............ ............ ............ ............ ... Page 14 of 52
Fig.6: Main Display Module (HMCC1024-6, HMCC1024-12) ............ ............ ....
Page 15 of 52
Fig.6A: Main Display Module (HMCC1024-6S, HMCC1024-12S) ............ ............
. Page 16 of 52
Fig.7: Adder Display Module ............ ............ ............ ............ ..... Page 17 of 52
Fig.8: Detection Adder Module ............ ............ ............ ............ ... Page 18 of 52
Fig.9: Signal Adder Module ............ ............ ............ ............ ...... Page 18 of 52
Fig.10: Relay Adder Module ............ ............ ............ ............ ...... Page 19 of 52
Fig.11: HUDACT-100 Digital Communicator Module ............ ............ .......... Page
19 of 52
Fig.12: City Tie Module ............ ............ ............ ............ .......... Page 20 of 52
Fig.13: Main Fire Alarm Module Terminal Connections ............ ............ ........ Page
21 of 52
Fig.14: Main Fire Alarm Module Terminal Connections (continued) ............ .........
Page 22 of 52
Fig.15: Detection Module Terminal Connections ............ ............ ............ . Page 23
of 52
Fig.16: Signal Module Terminal Connections ............ ............ ............ .... Page 24
of 52
Fig.17: Relay Module Terminal Connections ............ ............ ............ .... Page 25
of 52
Fig.17A:HUDACT-100 Terminal Connection ............ ............ ............ ...... Page 26
of 52
Fig.18: Polarity Reversal and City Tie Module Terminal Connections ............ ........
Page 27 of 52
Fig.19: Power Supply Connections ............ ............ ............ ............ Page 28 of 52
Fig.20: WIRING TABLE FOR INITIATING CIRCUITS ............ ............ ...........
Page 29 of 52
Fig.21: WIRING TABLE FOR INDICATING CIRCUITS ............ ............ ..........
Page 29 of 52
Fig.22: Indicators and Control Location ............ ............ ............ ........ Page 31 of
52
Fig.23: Configuration Indicators and Controls ............ ............ ............ ... Page 37
of 52Page 3 of 52
1.0 INTRODUCTION
Introduction :
Hochiki’s SERIES HCP 1000 Fire Alarm Control Units provide a large capacity of
supervised Class A or B (UL Style
D or B) Initiating Circuits, and supervised Class A or B (UL Style Z or Y)
Indicating Circuits. All Circuits are supervised
for opens and ground faults, and Indicating Circuits for shorts. Optional Modules
include additional Initiating and
Indicating Circuits, Relay, and Polarity Reversal & City Tie. Flush or surface
mountable enclosures can be used for
retrofits and on new installations.
1.1 Overall Features:
T Basic unit has 8 Class B (Style B) Initiating Circuits which may be configured as
4 Class A (Style D) Circuits.
These are configurable as Alarm, Verified Alarm, Waterflow Alarm, Sprinkler
Alarm, Latching or Non-Latching
Supervisory, or Trouble-Only Circuits. There are two LED’s per Circuit; one for
Trouble (Amber), and one for
Status (Red/Amber).
T Basic unit has 4 Power Limited Class A/B (Style Z/Y) Indicating Circuits with
individual trouble indicators. Each
Circuit can be configured as Audible (silenceable) or Visual (non-silenceable).
Audibles may be steady,
Temporal Code, California Code, or March Time.
T Initiating and Indicating Circuits may be individually Disconnected by a DIP
Switch (Slide-Switch on “S”
Versions for the USA Market only).
T Configurable Signal Silence Inhibit, Auto Signal Silence, Two-Stage Operation,
One-Man Walk Test.
T Subsequent Alarm, Supervisory, and Trouble operation
T Two outputs for 4 wire resettable smoke power supply (200 mA each Max., 300
mA total Max.)
T Auxiliary Relay Contacts for Common Alarm and Common Supervisory
(disconnectable), and a Common
Trouble relay.
T RS-485 Interface for HRA-1000 Series Remote Multiplex Annunciators.
T Optional Modules for additional Initiating, Indicating, & Relay Circuits,& City
Tie & Polarity Reversal Signalling.
T Easy Configuration via Push-Buttons and Switches.
T Extensive transient protection
T Surface Mountable Enclosures, Flush Trims Available
1.2 Controls and Indicators: 8 Push-Buttons, 16 Common Indicators, provision for
up to 24 Circuits
(Expansion Chassis adds provision for up to another 48 Circuits)Page 4 of 52
2.0 GENERAL NOTES
Number of Adders that may be Installed:
The maximum number of Circuit Adder Modules that may be physically installed
in a System is ...
Main Chassis Type
HMCC1024-6(S) or HMCC1024-12(S) Two Circuit Adder Modules of any type.
HMCC1024-6(S) or HMCC1024-12(S) and HECH1048 Eight Circuit Adder
Modules of any type.
The “S” Version Chassis’ have Slide-Switches instead of DIP Switches for
Disconnects. The maximum number of each
Circuit Adder Module type is ...
A maximum of 7 HDM-1008A 8 Initiating Circuit Modules (total of 64 Initiating
Circuits in a system).
A maximum of 5 HSGM-1004A 4 Indicating Circuit Modules (total of 24
Indicating Circuits in a system).
A maximum of 4 HRM-1008A 8 Relay Circuit Modules (total of 32 Relay Circuits
in a system).
MAXIMUM OF 8 ADDER MODULES OF ANY COMBINATION PER
SYSTEM.
Any HCP-1000 System may have a HPR-100 or HUDACT-100 added, and up to
eight (8) Remote Multiplex
Annunciators externally. As good practice, it is recommended that Circuit Adder
Modules be installed in the order
of Signals followed by Detection, followed by Relay Modules.
Circuits and Zones:
“Circuits” refers to an actual electrical interface, Initiating (Detection), Indicating
(Signal), or Relay.
“Zone” is a logical concept for a Fire Alarm Protected Area, and will consist of at
least one Circuit.
Often the terms Zone and Circuit are used interchangeably, but in this Manual the
term Circuit is used.
Display Points:
On the HCP-1000 an important concept is Display Points. Unlike some products
the available LED Displays and
matching Circuit Disconnect Switches are not hard-wired to the Circuit Adder
Modules. The Main Fire Alarm Module
and each Circuit Adder Module type have a required number of Display Points
specified. In the case of Initiating
Circuits this will be reduced by half if Class “A” operation is selected. Different
Main and Expander Chassis provide
a fixed number of Display Points on their attached Display Boards. These are
assigned during the Configuration Adder
Module Number and Type operation (see Configuration Section) as required in the
cabling order in which Adder
Modules are installed. In any system setup, there must be at least as many Display
Points available, as those required
by the Circuits.
Wiring Styles:
Initiating Circuits are configured by default as Class B (Style B). They may be
globally (all or none) configured as
Class A (Style D) as described in the Configuration Section. This operation uses
odd and even pairs of two-wire Class
B (Style B) circuits to make one four-wire Class A (Style D) circuit, thus cutting in
half the number of available Initiating
Circuits.
Indicating Circuits may be individually wired as Class A (Style Z) or Class B
(Style Y) without affecting the number
of circuits available (see Module wiring instructions).Page 5 of 52
3.0 SYSTEM COMPONENTS
Model: HBB-1024 Surface Enclosure 24 Circuits
HBB-1072 Surface Enclosure 72 Circuits
(add suffix R for Red Enclosure)
Model: HFA-1024TR Flush Trim Ring
HFA-1072TR Flush Trim Ring
(add another suffix R for Red Enclosure)
Model: Batteries (6.5 to 40 AH)
Model: HMCC1024-6 6 A Main Chassis
HMCC1024-12 12 A Main Chassis
(add Suffix S for Slide Switches)
Model: HECH1048 48 Display Expander Chassis
Model: Circuit Adder Modules
HDM-1008A, HSGM-1004A. HRM-1008A,Page 6 of 52
Model: HPR-100 Polarity Reversal and
City Tie Module
HRA-1000 Series Remote Multiplex
Annunciator Panels
3.1 CHASSIS TYPES
Model: HMCC1024-6 Main Chassis with 8 Style B / 4 Style D Initiating Circuits,
4 Style Y or Z Indicating
Circuits, and a 6 ampere Power Supply. See Module Specifications for more detail.
Model: HMCC1024-12 Same as HMCC1024-6, but with a 12 ampere Power
Supply. See Module Specifications
for more detail.
Model: HMCC1024-6S Same as HMCC1024-6, but with Disconnect Slide
Switches instead of DIP Switches.
Model: HMCC1024-12S Same as HMCC1024-12, but with Disconnect Slide
Switches instead of DIP Switches.
Model: HECH1048 Expander Chassis for up to 48 additional Zones / Circuits. DIP
Switches for Disconnect
only. See Module Specifications for more detail.
3.2 HCP SERIES 1000 FIRE ALARM CONTROL PANEL - KITS
Model: HCP-1008E Expandable Kit for the Canadian Market, 8 Class B (or 4
Class A) Initiating & 4 (Class
A or B) Indicating Circuits, Expandable to 24 Circuits, 6 Amp Power Supply
(HMCC1024-
6 Main Chassis in a HBB-1024 Enclosure).
Model: HCP-1008ES Expandable Kit for the USA Market, 8 Class B (or 4 Class
A) Initiating & 4 (Class A
or B) Indicating Circuits, Expandable to 24 Circuits, 6 Amp Power Supply
(HMCC1024-6 Main Chassis in a HBB-1024R Enclosure).
For any other sizes, etc., components are ordered separately.Page 7 of 52
Fig.1: HBB-1024 Flush or Surface Enclosure Installation and Dimensions
4.0 MECHANICAL INSTALLATION and DIMENSIONS
Install the enclosure as shown for the HBB-1024 (Fig.1) or HBB-1072 (Fig.1A)
...Page 8 of 52
Fig.1A: HBB-1072 Flush or Surface Enclosure Installation and DimensionsPage 9
of 52
Fig.2: Main Chassis Installation
4.1 MAIN CHASSIS INSTALLATION
The Main Chassis is installed in the HBB-1024 Backbox as shown using the
supplied hex-nuts. Group the incoming
wires through the top of the enclosure to prepare it for wiring the Modules. Do not
run the wires in-between the
Modules since it could cause a short circuit. Use a wire tie to group wires for easy
identification and neatness.
Be sure to connect a solid Earth Ground (from building system ground / to a cold
water pipe) to the Chassis Earth
Ground Mounting Lug, and to connect the Earth Ground Wire Lugs from the Main
Chassis to the ground screw on the
Backbox.Page 10 of 52
Fig.3: Expander Chassis Installation
4.2 MAIN & EXPANDER CHASSIS INSTALLATION
The Main and Expander Chassis’ are installed into the HBB-1072 Enclosure as
shown using the supplied hex-nuts.
Group the incoming wires through the top of the enclosure to prepare it for wiring
the Modules. Do not run the wires
in-between the Modules since it could cause a short circuit. Use a wire tie to group
wires for easy identification and
neatness.
Be sure to connect a solid Earth Ground (from building system ground / to a cold
water pipe) to the Chassis Earth
Ground Mounting Lug, and to connect the Earth Ground Wire Lugs from BOTH
the Main Chassis and the Expander
Chassis to the ground screw on the Backbox.Page 11 of 52
5.0 MODULES MOUNTING LOCATIONS
The Main Chassis’ in a HBB-1024 or HBB-1072 Enclosure come pre-assembled
with all power supply, main panel, and display
components and boards. The Expander Chassis has the display board pre-
assembled. The HPR-100 City Tie Module or
HUDACT-100 Digital Communicator may be added on the left side, as shown in
the figure on the following page. These
Modules connect directly to the dedicated P2 connection in the upper-left corner of
the Main Fire Alarm Module. Circuit Adder
Modules are installed from right to left using the supplied stand-offs, as shown in
the figure on the next page, with the first Module
plugging its 26 pin ribbon cable into P5 on the Main Fire Alarm Module, and using
the included HMD-579 four wire power cable
as described in the Module Settings section. A second Circuit Adder Module
would connect by plugging its 26 pin cable into the
matching socket on the previous module to the right, and by installing the supplied
HMD-579 four wire power cable as described
in the appropriate Module Settings section.
In a HBB-1072 Enclosure with an Expander Chassis, there are two each of long
extension cables for the 26 pin ribbon cable
(HMD-575) and for the four wire power cable (HMD-580) included. Circuit Adder
Modules are installed as on the Main Chassis,
from right to left in two tiers (back then front). These are cabled as in the Main
Chassis, except that the first module on the back
tier to the right connects via HMD-575 and HMD-580 extension cables to the
second module in the Main Chassis, and the fourth
module on the front tier to the right connects via HMD-575 and HMD-580
extension cables to the third module on the first tier to
the left. In other words a continuous right to left, bottom to top, and back to front
installation order (see the figure on the next
page).
To enable communication from the Main Fire Alarm Module to all of the Circuit
Adder Modules, it is necessary to remove the
Continuity Jumper on JW6 (near P5, the Circuit Adder Module Connector) on the
Main Fire Alarm Module. This jumper plug must
be installed on the Continuity Jumper on the last installed Circuit Adder Module
(see the appropriate Module Settings section
to verify the location of theContinuity Jumper on a particular Circuit Adder
Module). Only the LAST Circuit Adder Module should
have a jumper plug on its Continuity Jumper; all others must be left without a
jumper plug !!
There needs to be enoughDisplay Points for each circuit on an Adder Module, and
these are assigned during Configuration (see
Configuration Section) in the order in which the Adders are electrically installed
(the order in which they have their cables
connected to each other). Both the number of points available for each Display
Type, and the number required for each Circuit
Adder Module Type are described in the Module Settings Section.
As good practice, it is recommended that Circuit Adder Modules be installed in the
order of Detection followed by Signals, followed
by Relay Modules.Page 12 of 52
Fig.4: Module Mounting LocationsPage 13 of 52
Fig.4A: Circuit Adder Module Mounting DetailsPage 14 of 52
Fig.5: Main Fire Alarm Module
6.0 MODULE SETTINGS
6.1 MAIN FIRE ALARM MODULE (Part of Main Chassis)
JW5Jumper installed for Class A (Style D) operation of Initiating Circuits 1 and 2.
JW1Jumper installed for Class A (Style D) operation of Initiating Circuits 3 and 4.
JW2Jumper installed for Class A (Style D) operation of Initiating Circuits 5 and 6.
JW3Jumper installed for Class A (Style D) operation of Initiating Circuits 7 and 8.
JW6Continuity Jumper removed if there are any Circuit Adder Modules installed,
and installed on the last Circuit Adder Module.
JW4Jumper removed if a HPR-100 Module or HUDACT-100 is installed.
P1 RS-485 Connection for future expansion. P2 Connector for HPR-100 Module
or HUDACT-100.
P3 Connector for Display Module (part of HMCH-1024). P4 Connector for future
expansion.
P5 Connector for Circuit Adder Modules. P6 Power Connector for Adder Modules.
P7,8 Factory connection to Bridge Rectifier. P9,10 Connection to 24 VDC Battery.
The Main Fire Alarm Module contains the following Circuits, each requiring a
certain number of Display Points ...
Chassis Type Initiating Circuits Indicating Circuits Display Points Required
HMCC1024-6(S) 8 Style B / 4 Style D 4 Style Y or Z 8 /4 (Style B / D)
HMCC1024-12(S) 8 Style B / 4 Style D 4 Style Y or Z 8 /4 (Style B / D)
Note that the Main Display Module (part of the Main Chassis) has 4 dedicated
Display Points for the 4 Indicating Circuits on the Main Fire
Alarm Module.Page 15 of 52
Fig.6: Main Display Module (HMCC1024-6, HMCC1024-12)
6.2 MAIN DISPLAY MODULE (Part of Main Chassis)
P1 Cable connects to P3 of Main Fire Alarm Module.
P2 Connection to P1 of HECH1048 Display Module if used.
SW1 to SW5 See Configuration & Operation sections of Manual.
The Main Display Module provides 4 dedicatedDisplay Points for the 4 Indicating
Circuits on the Main Fire Alarm Module. It also provides
the following general purpose Display Points ...
Chassis Type Display Points
\ There are also 4 Display Points dedicated to the 4 Main Board Indicating Circuits.
HMCC1024-6 24 > The first 8 or 4 of these (depending upon Style B or D
operation) are dedicated
HMCC1024-12 24 / to the 8 / 4 Main Board Initiating Circuits.
Note: The Main Display Module comes with a Label Sheet (NP-680) including
both English and French slide-in labels. This sheet may be
run through a Laser Printer for labelling purposes before being installed. The first
slide-in section comes in two versions; one for Single-Stage
Systems, and one for Two-Stage Systems.
O
n
t h
e
H
M
C
C
1
0
2
4 -
6
S
a
n
Tải về để xem bản đầy đủ
83 trang
12520
Free
Bạn đang xem 20 trang mẫu của tài liệu "Hướng dẫn sử dụng trung tâm báo cháy Hochiki thường", để tải tài liệu gốc về máy hãy click vào nút Download ở trên
File đính kèm:
- huong_dan_su_dung_trung_tam_bao_chay_hochiki_thuong.docx
